This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Other. The cookies is used to store the user consent for the cookies in the category "Necessary". The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category "Functional". The cookie is used to store the user consent for the cookies in the category "Analytics". These cookies ensure basic functionalities and security features of the website, anonymously. 850-900Necessary cookies are absolutely essential for the website to function properly. The reed valve is located in a reed plate that is Diaphragm should be renewed if air leaks or cracks are defective or questionable parts should be Vacuum pulsa-tions from the engine crankcase. Side of power head cylinder blOCk and is actuated by pressure and Adjust float level by bending floatįUEL PUMP. (0.47-0.55 in.) away from sealing ring surface of carburetor body remove float bowl (7) and invertĬarburetor body (1). Main fuel metering is controlled by main jet (2). Stop screw (12) so engine idles at approximately 900-1000 rpm.Īdjust pilot air screw so engine idles smooth and will accelerateĬ1eanlv without hesitation. Operating temperature and running in forward gear. FinalĬar-buretor adjustment should be made with engine at normal Initial setting of pilot air screw (15)įrom a lightly seated posi-tion should be 3/.-11/. to en-sure a water tight seal.ĬARBURETOR. Reinstall vent and fill plugs securely using a new gasket, if The lower unit gears and bearings are lubricated byĪpproximately 85 mL (2.9 ozs.) of SAE 90 hypoid outboard gear oil. Gasoline and oil should be thoroughly mixed. Regular or no-lead automotive gasoline having an 85-95 octane fuel :oil ratios should be 20:1 duringīreak-in and 30:1 for normal service. The power head is lubricated by oil mixed with the fuel.įuel:oil ratios should be 30:1 during break-in of a new or rebuiltĮngine and 50: 1 for normal service when using a BIA certified TC-WĮngine oil or Suzuki "CCI" oil. 22-35 N'm (195-310ĬONDENSED SERVICE DATA NOTE: Metric fasteners are used NOTE: Metric fasteners are used throughout outboard motor.
SUZUKI DT4 OUTBOARD MOTOR MANUAL SERIAL NUMBER
ForĮxample, if first number in serial number is 1, model year is The first number in serial number corresponds with model year. The years 1977, 19 are identifiedīy the letters "C," "D" and "F" respectively. The first character of serial number indicates Six characters indicate the model and second six characters are Motors, refer to numbers located on motor clamp bracket. 22-35 N'm (195-310 in.-Ibs.)ġb determine model and year of manufacture of Suzuki outboard 3.0 mm (0.118 in.) TIGHTENING TORQUES Cylinder Head. See Text SIZES-CLEARANCES Piston Ring End Gap. Crankshaft Runout at Main Suzuki OT2 Bore. CONDENSED SERVICE DATA NOTE: Metric fasteners are used throughout outboard motor. For example, if first number in serial number is 1, model year is 1981. Starting with 1980, the first number in serial number corresponds with model year. The years 1977, 19 are identified by the letters "C," "D" and "F" respectively. The first character of serial number indicates year of manufacture. The first six characters indicate the model and second six characters are motor serial number. Box 1100 Brea, California 92621 SUZUKI DT2 1b determine model and year of manufacture of Suzuki outboard motors, refer to numbers located on motor clamp bracket.
SUZUKI DT4 OUTBOARD MOTOR MANUAL MANUAL
SERVICE MANUAL TUNE-UP SUZUKI SUZUKI AMERICA CORPORATION 3251 E.
0 kommentar(er)
